420 tons of t

PRODUCTS HANDBOOK Structural Steel

CONTINENTAL STEEL PTE LTD 100 Gul Circle, Singapore 629586. Phone: (65) 68620033 Facs: (65) 68616448/68624006. Website: www.consteel.com.sg PRODUCTS HANDBOOK Structural Steel Subsidiary Companies: Continental Hardware (M) Sdn Bhd

Get Price

410 / 420

Bar Specifications Uns Type Ams Astm Federal Characteristics S41000 410 5613 A-276 A-314 A-479 A-493 QQ-S-763 410 is a low cost general purpose stainless steel, that hardens at 35-39 RC and is used widely where corrosion is not severe. S42000 420 5621

Get Price

MATERIAL DATA SHEETS FOR STRUCTURAL STEEL

M-CR-120, Rev. 1, December 1994 page 6 MATERIAL DATA SHEET MDS - Y03 Rev. 1 TYPE OF MATERIAL: Structural Steel, Grade 355 PRODUCT STANDARD GRADE Plates and sections Seamless tubulars EN 10 025 prEN 10225 S 355 J2 G3 NO 1 ...

Get Price

The Hot Rolling Process

The Hot Mill rolls slabs weighing up to 30 tons between 30” and 74”. Steel slab 8 to 9 inches thick and up to 36 feet long is rolled into strip as thin as 1/16 inches and up to a half-mile in length. Coils are produced with a 30” inside diameter (‘eye’) on one of two ...

Get Price

Ball Mill Design/Power Calculation

The basic parameters used in ball mill design (power calculations), rod mill or any tumbling mill sizing are; material to be ground, characteristics, Bond Work Index, bulk density, specific density, desired mill tonnage capacity DTPH, operating % solids or pulp density, feed size as F80 and maximum ‘chunk size’, product size as P80 and maximum and finally the type of circuit open/closed ...

Get Price

BAR DATA HANDBOOK AISI/SAE

The rolling mill is equipped with a walking beam furnace with a capacity of 125 tons per hour. Blooms are de-scaled after exiting the furnace, and then proceed through a five stand roughing mill, a six stand intermediate mill, and an eight stand finishing mill

Get Price

5 in. Giddings & Lewis Table Type Horizontal Boring Mill …

5 in. Giddings & Lewis Table Type Horizontal Boring Mill Model 65-H5-T, S/N 420-41-62, 72 in. Vertical, 48 in. x 98 in. Table Surplus Equipment Due to Relocation of Forging Company Ends from

Get Price

T-42 super-heavy tank

Type Super-heavy tank Place of origin Soviet UnionProduction history Designer Edward Grote Designed 1930–1932 No. built 0 Specifications (T-44A) Mass 101.6 tonnes (112 short tons; 100 long tons)Length N/A Width N/A Height N/A Crew 14-15

Get Price

Gerdau Plant In Fort Smith Produces 500,000 Tons Of Steel …

 · Keeping the automotive and agriculture industry in stock with high-quality steel for forging components is Gerdau’s North American special steel mill in Fort Smith. The facility at the end of Planters Road has been running at full capacity, 24 hours a day, to produce 500,000 tons of special bar quality steel billets a year.

Get Price

ASTM A615 / A615M

1.2 Unless specified for use for other applications in Annex A2, bars are of four minimum yield strength levels: namely, 40 000 psi [280 MPa], 60 000 psi [420 MPa], 80 000 psi [550 MPa], and 100 000 psi [690 MPa], designated as Grade 40 [280], Grade 60 [420], Grade 80 [550], and Grade 100 [690], respectively.

Get Price

Asphalt Tonnage Calculator | Asphalt Volume Calculator | …

Asphalt is a black cementitious material, made by fractional distillation of crude petroleum. This online Asphalt Volume Calculator helps you to estimate the Asphalt tonnage required for making a pavement of a specified length, width and thickness.

Get Price

Calculate Ball Mill Grinding Capacity

The sizing of ball mills and ball milling circuits from laboratory grinding tests is largely a question of applying empirical equations or factors based on accumulated experience. Different manufacturers use different methods, and it is difficult to check the validity of the sizing estimates when estimates from different sources are widely divergent. It is especially difficult to teach mill ...

Get Price